Wheels

Authentic service bearing kit for Ritchey mountain bike wheels. - Replacement bearings for Vantage V1 non-2pc hubs

Big Deal spoke nipple washers are not required for tubeless set up. When used, they eliminated the need for tubeless tape.

Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.

Stan's lightweight aluminum valve stems are half the weight of Stan's standard brass valves. The secure round base is compatible with most tubeless rims and a perfect fit for all Stan's BST rims. A removable valve core makes adding sealant easy, and these babies fit up to 8mm valve hole. Sold as a pair.

EX 1700 SPLINE wheels feature a super strong and welded 30 mm wide aluminum rim with a profile design made to withstand the hardest use of Enduro racing, while still keeping the weight low for long and demanding uphills. Laced to double butted competition straightpull spokes, the EX 1700 SPLINE wheels are built to take a beating. - Welded Aluminum rim with 30mm internal width - 350 hub with 36 point SL Ratchet system - Competition spokes and Squorx nipples - Designed for Enduro applications

The Wolf Tooth Rear Axle uses a captive steel washer under the head to reduce friction on the dropout face. This protects your expensive frame, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. - Made in Minnesota to aerospace standards

- Dynamo generator front hub features 3.0-watt headlight power supply - A356 aluminum hub shell with 9mm solid nutted axle (140mm overall axle length) - Choose 70mm or 90mm drum brake (brake levers sold separately) - Light sold separately

Proterra Tough i30 wheels keep the trail in check while everything else blurs by in the periphery. Reinforced by our proven Dual I-Beam support, Proterra Tough rims feature a 30mm internal width to provide higher tire volume while also increasing sidewall support at lower pressures. High-quality EZO sealed bearings are designed to endure through seasons of aggressive riding, while a responsive 6-pawl freehub provides the snappy 3.7 degrees of engagement you demand when cranking out of corners. Choose Proterra Tough when you need a wheel that won't let you down. - 30mm inner rim width with 32 spokes laced in a 3-cross pattern - 6069 aluminum alloy rim is TCS 2.0 tubeless-ready - Sapim Secure Lock 14-gauge brass nipples provide bomber durability, while double butted 2.0/1.8/2.0mm J-bend spokes make replacement a breeze. - Tubeless tape, Solid Strip, and black alloy valves are preinstalled, making the wheels ready for tubeless tires the moment they arrive on your doorstep. The TCS 2.0 Solid Strip is a durable strip that lies beneath the tape, prevents it from sagging at the spoke holes, makes it easier to mount a tire, and protects from puncture in the case of a broken spoke. - 6-bolt rotor mounts - Top-tier EZO sealed bearings

- Tough on trail and light on price rated for everything from XC to Enduro and E-bike - Steel axles cartridge bearings robust alloy hub shell and steel cassette body - 10-degree pawl engagement - International Standard 6-bolt disc mount - *Shimano/SRAM

These die-cut borderless decals provide a distinctive look to go with the distinctive sound and aero-advantage of Zipp wheels rolling at 45km an hour. Zipp’s Matte white and Matte black decals also are still available. Each decal kit has seven decals sufficient to cover one wheel and two matching valve-hole decals. Note: Before applying the decals, make sure the rim surface is free of dirt and debris. We recommend a gentle wipe with acetone or rubbing alcohol. Peel the white backing sheet from the decal, orientate, position and gently press the decal onto the rim surface. Starting at one end, remove the surface clear cover slip and then work the decal into the dimples using a 3M squeegee.

A non-tubeless protective strip to cover the spoke holes in your ENVE carbon clinchers. 

The ARC Offset rims utilize an asymmetrical design to optimize spoke tension balance, wheel durability, and wheel stiffness. Its 6069 Alloy construction provides a superior strength-to-weight ratio, significantly improving toughness. - Offset nipple bed for improved spoke tension balance and wheel strength/stiffness - Strong tire retention bead - Tubeless ready

Product specs: - Str tubeless ready - Size: 27.5", 29" - Outside width: 40mm - Inner bead width: 36mm - Weight: 27.5"-515g, 29"-550g - Double wall welded rim (sleeved rims available oem only) - Brake compatibility: disc only - Hole count: 28/32

The CADEX 36 Disc WheelSystem is a versatile, lightweight composite wheel built for real-world performance. Featuring a hookless rim design with optimal 22.4mm internal width and 36mm depth, it delivers unbeatable acceleration and climbing efficiency as well as confident handling on descents, in the wind and on varied terrain. - Precision reinforced lay-up places carbon fiber only where needed, creating a strong, stiff rim structure weighing in at only 1302 grams. - Dynamic Balanced Lacing technology produces a stiffer, more efficient wheel with outstanding power transfer. - High tensile strength CADEX aero carbon spokes minimize lateral flex for more efficient acceleration and climbing. - The 22.4mm inner rim width creates an increased actual tire contact patch for better traction and impact absorption, better handling, more confidence and less rider fatigue. - CADEX hookless rim technology features a broad inner rim width and durable continuous carbon fiber structure, helping create a rounder tire shape for superior grip and handling plus added sidewall support when cornering, all without compromising weight. - The precision machined low-friction R1-C30 hub significantly reduces bearing load as CADEX ceramic bearings further increase efficiency by offering lower rolling resistance and 1.5x smoother action than steel. - A low 36mm rim profile offers excellent stability in shifting winds.

Introducing the Gravel racing GRC 1400. With a holistic approach of engineering DT re-thought the characteristics of a modern benchmark setting gravel wheel set. Aerodynamic efficiency, ideal support of wide gravel tires leading to comfort and traction off-road as well as remarkable durability are only some of the key features that make this wheel set the perfect companion for your next gravel adventure. - 42mm aero-optimized rim depth for 35mm wide gravel tires

Lightweight and easy to install, there are Ritchey rim strips for all wheel sizes and types. - Easily snaps over your rims - Stretchy, tightly woven material provides a close fit and protects from abrasion - Sold as a pair - Not for tubeless set up

When motor assistance and leg power meet, the range of terrain a bike can conquer grows almost exponentially. The H 1900 SPLINE is designed for this, now upgraded with the famous DT Swiss Ratchet technology. The Ratchet LN system distributes the combined forces from the rider and the motor over a larger area than the previous pawl freehub systems, increasing the systems’ durability thanks to lower load peaks. The 370 hub enables full power transmission to the ground with reinforced hybrid spokes laced to a resistant aluminum rim, available in two inner widths. - Aluminum rim, Hooked / Crotchet tubeless ready - DT Hybrid 1 spokes are reinforced and increase the lateral and torsional stiffness of the wheel - 370 Hub - Includes Tubeless Valve and Tape, 6-bolt adapter with lockring

- Replacement freehub bodies include pawls and springs pre-installed - M-Pulse hubs: six pawls are equipped with Neodymium magnets engaging every 1.66 deg - E-Sync hubs: fast 8.18 deg engagement with reinforced high-torque pawls - HG 11sp road FH body

- Replacement freehub bodies include pawls and springs pre-installed - M-Pulse hubs: six pawls are equipped with Neodymium magnets engaging every 1.66 deg - E-Sync hubs: fast 8.18 deg engagement with reinforced high-torque pawls - HG 11sp road FH body

Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3

After a long climb, the perfect trail lies ahead of your tires: flowy, dusty, varied, endless. Nothing holds you back from entering the All-Mountain thrills with the M 1900 Spline wheels. A rim developed with optimal balance of durability and weight offers efficient climbing characteristics as well as dent resistance on single trails. With experienced wheel building by hand, this wheel is a reliable partner to collect freewheeling moments in the mountains. - Intended use = XC and All-Mountain/Trail - Tubeless ready, 30mm wide and light rim - Straight-pull hubs/spokes built with a 3-cross pattern - Includes Tubeless Valve and Tape, 6-bolt adapter with lockring

Your entire focus lies on the right line choice, the exact braking point and the spot-on steering movement. All the everyday stress fades away, you feel free and only hear the precise sound of the freehub system. The E 1900 Spline wheels were developed precisely for these freewheeling moments. A proven aluminum rim and hand-laced steel spokes provide the reliability required from an Enduro wheel. - Intended use = All-Mountain/Trail, Enduro and Freeride - Tubeless ready, 30mm wide and light rim - Straight-pull hubs/spokes built with a 3-cross pattern - Includes Tubeless Valve and Tape

After a long climb, the perfect trail lies ahead of your tires: flowy, dusty, varied, endless. Nothing holds you back from entering the All-Mountain thrills with the M 1900 Spline wheels. A rim developed with optimal balance of durability and weight offers efficient climbing characteristics as well as dent resistance on single trails. With experienced wheel building by hand, this wheel is a reliable partner to collect freewheeling moments in the mountains. - Intended use = XC and All-Mountain/Trail - Tubeless ready, 30mm wide and light rim - Straight-pull hubs/spokes built with a 3-cross pattern - Includes Tubeless Valve and Tape, 6-bolt adapter with lockring

Industry Nine Hydra Classic hubs are the heart of your wheelset, everything revolves around them, literally. Every Classic Hydra hub is made start to finish in Asheville, NC. From turning and milling bar stock 7075-T6 aluminum for shells, axles and encaps, wire EDM cutting A2 tool steel for pawls and driverings, to in-house anodization lab, every step of design, engineering, manufacturing and assembly is done to exacting standards. - 690 P.O.E. Hydra Freehub body engages every .52 degrees yeilding telepathic control - 6 pawl, 6 phase - 115 tooth drivering - Easily serviced with no proprietary tools. Designed to keep you in the saddle and out of the service queue - Classic j-bend spoke interface - Steel cartridge bearings are durable

EXC 1501 SPLINE ONE combines everything a modern enduro rider wants in a wheel. The 30 mm wide carbon rim gives you the precision to stay on track even on the trickiest lines while a 240 hub keeps it spinning. Both components are held together by performance weight optimized competition race straightpull spokes. - Designed for Enduro applications - Carbon rim with 30mm internal width - 240 hub - Competition race spokes and Squorx nipples

Industry Nine Hydra Classic mountain hubs are loaded with features every rider will appreciate such as revolutionary 0.52° engagement, generously low weights and an intuitive layout that can be serviced without any proprietary tools. - From turning and milling bar stock 7075-T6 aluminum for shells, axles and encaps, wire EDM cutting A2 tool steel for pawls and driverings, to in-house anodization lab, every step of design, engineering, manufacturing and assembly is done to exacting standards in Asheville, NC - 690 P.O.E. Hydra Freehub body engages every .52 degrees yeilding telepathic control - Classic j-bend spoke interface - Steel cartridge bearings are durable - Easily serviced with no proprietary tools; Designed to keep you in the saddle and out of the service queue

SMOOTHER IS FASTER Trail riders who prize nimble handling will be blown away by Traverse SL II's category-leading control, strength-to-weight ratio, and pinch-flat resistance. LIGHTER At 1,645 grams, this is our lightest trail wheelset ever. STRONGER Front and Rear Specific Rims with carbon layups optimized for strength and weight boast 15% greater front wheel strength and 25% more rear wheel strength than the previous Traverse SL. CONTROL-BOOSTING VERTICAL COMPLIANCE 21% more vertically compliant than the previous Traverse SL (delivered through Shallow Rim Shape and front/rear specific layup) enables enhanced terrain hugging and bump-force absorbing control. TRACTION MONSTER Carefully engineered rim shape intentionally flexes for improved support and traction to boost confidence and control. TOUGH LIFE, LONG LIFE Engineered rim offset enables balanced spoke tension for improved fatigue life. Lifetime warranty on Roval Wheels when registered within the first 90 days of purchase. SAYONARA PINCH FLATS Optimized "Flat Top" bead profile requires 85% more force to pinch flat compared to a standard round bead, virtually eliminating "snake bites." AIR TIME Thank our genius engineer Chuck Teixeira for inventing the "Roval ThreadBed Valve"; a valve that threads directly into the rim eliminating compression nuts, air loss from rim flex, and makes tire set-up easier, and reduces sealant clogs. INTENDED USE Trail WEIGHT (29) 1,645g 240 EXP (with valve and tape) WHEEL SIZES: 29 2 Year "It Happens" No Fault Crash Replacement - If you damage your Roval product while riding within the first two years of ownership and it's not covered under warranty, we'll still replace or repair. USA Only and wheels must be registered. STRUCTURAL WEIGHT LIMIT (Rider & Cargo) - 125kg / 275lbs

Replacement freehub bodies for Vault hubs. - Use to replace worn/damaged freehub body or to switch cassette standards. - 60T

- TSE design with 23mm internal width with tubeless and hookless rim profile ideal for wider tires at lower tire pressure - Minimum 25mm tire width - More than 300 g lighter than previous model - ZR1 DB hub is engineered in Germany with better seal design for improved durability and quicker response with 66 points of engagement - An all-out aero 80mm rim profile - ABLC Sawtooth dimple design helps manage air flow around the rim, and contributes to create a faster, more stable wheel - Center locking rotor interface. Lockring is included - Lifetime warranty

Who knew we could make a thru axle disappear? The Maxle Stealth offers a light, low profile alternative to Maxle Lite. Features - 34g lighter than Maxle Lite - Easy installation with a 6mm Allen wrench